Power Wagon Advertiser Forums Vintage Powerwagons Power Wagon Advertiser Magazine

Go Back   Power Wagon Advertiser Forums > MILITARY & CIVILIAN DODGE TRUCK RELATED FORUMS > Service & Repair Procedures includes body/frame repair & painting

Notices

Service & Repair Procedures includes body/frame repair & painting Useful technical content, information or questions applicable to many or all of our truck models; mechanical, electrical, body & paint, tire, restoration, whatever...

Reply
 
Thread Tools Display Modes
Old 01-26-2014, 09:15 PM   #91
Charles Talbert
Subscriber
 
Join Date: Jul 2003
Location: Norwood, N.C.
Posts: 2,625
Adding that much shim to get correct end play is not unusual at all; it is designed that way. The more you talk, the more it sounds like there is no real issue. I think a double check to ease your mind is in order, but I don't really expect a bad report.
__________________
www.mseriesrebuild.com
Charles Talbert
Charles Talbert is offline   Reply With Quote
Old 07-04-2015, 10:45 AM   #92
CSCameron
Registered
 
Join Date: Mar 2012
Location: Cave Creek, AZ
Posts: 348
I know this is an old thread, but I just finished reading all it because I am beginning my MU2 rebuild... excellent! This will be an invaluable resource. MaineSS, Thanks for taking the time to document the process.

Clark
CSCameron is online now   Reply With Quote
Old 04-03-2017, 12:53 AM   #93
RicherRacing
Premium Forum User
 
RicherRacing's Avatar
 
Join Date: Jul 2014
Location: San Diego County
Posts: 58
Quote:
Originally Posted by maineSS View Post
There are a couple of trouble spots in reconditioning the worm shaft bearings. The first is removing the bearing races from the retainers, and the second is setting the proper bearing preload.
Pic #29 shows the retainer in a vice prior to removing the bearing seal. The seal is easily removed and replaced with a suitable dia rod and a few hammer taps. The bearing race is quite difficult to remove by forcible methods, as access to the backside is very limited (pic #30). I initially tried freezing the race with a special cold spray, but it still required a lot of hammering with a mini-sledge on my mini cats-paw. You need to have the retainer held in a 6" or larger vice with the cats-paw alongside the lower half of the vice (pic #31). Hit the top of the cats-paw with a drift, and move around the race at 180 deg intervals. If you have access to welding equipment, the next post will show you a MUCH easier way....
My neighbor came up with a clever way to remove the bearings for my winch. He made a split flanged tool which was installed flange end in from the bearing side. The thin flange fits on the back side of the bearing race. Once installed, the tool is spread so the flange goes behind the race. Then flip it over and press out from behind.
Attached Images
File Type: jpg IMG_9067.jpg (64.7 KB, 59 views)
File Type: jpg IMG_9071.jpg (57.6 KB, 60 views)
RicherRacing is offline   Reply With Quote
Old 04-06-2017, 09:38 AM   #94
Matthew Welcher PWA
Administrator
 
Matthew Welcher PWA's Avatar
 
Join Date: Jun 2009
Location: Fairfield Iowa
Posts: 335
That removal tool is a very nice set up!
__________________
1967 W200
1946 WDX
Life is easier in a lower gear.
Matthew Welcher PWA is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are Off
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:59 PM.


Powered by vBulletin®
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright ©2002 - 2016, Power Wagon Advertiser. All rights reserved.